Feather Board FAQ Guide-Make Feather Board for your Table Saw

A popular accessory in thewoodworking industryis the feather board for stationary power tools. This accessory serves as a safety measure to reduce accidents from power tools.

Although several technicians and woodworkers utilize this accessory, many questions remain unanswered.

Hence, this article presents answers to frequently asked questions about the feather board. You will also learn about different types of feather boards and how to use them for precise cuts.

Figure 1:

A FeatherBoard on a Router Table

Section 1: What is a feather board?

1.1 What is a feather board?

A Featherboard is a hold-down device that operators use in holding their workpieces in place. This device helps to hold the workpiece against a machine fence or tool surface due to its design.

Many inaccuracies and errors arise when using power tools to cut materials. These errors are typically due to mechanical vibration. Therefore, they are often very difficult to manage or correct. As a rule of thumb, the feather board is a power tool add-on that helps you avoid inaccurate cuts.

The evolution of power tools has put forward the need for safety when using such machines. The feather board also offers you protection due to its modern design for protecting against kickbacks.

Figure 2: Featherboard on a table saw.

Featherboard on a table saw.

1.2 What is the purpose of the feather board?

Thefeather boardis famous for two essential purposes, namely;

To hold-down your workpiece

A vital application of your feather board is to hold your workpiece tightly. This particular functionality is integral to the type and quality of cut you can make on your workpiece. Often, some users have to carry out precision tasks on theirtable saws. These precision tasks usually require proper handling. As such, the feather board is very effective when precise cuts and consistent pressure are critical.


Although power tools are famous for their effectiveness, they are also known to cause some serious injuries. As such, the feather boards helps to prevent your hands from moving too close to your saw blade. This accessory also allows for easy maneuver of your stock in your cut’s direction without reverse movements.

These advantages make a feather board a must-have tool for precision tasks. They are also essential when accuracy and safety are crucial.

Section 2: Why use feather boards?

Numerous accessories enhance the performance of power tools. Therefore, operators have to decide on which accessory is best to use with their power tool. If you are looking to improve your cutting results, then the feather board is a must-have.

feather board and router table

feather board and router table

Here are the different reasons why you must use the feather board.

1. Easy to set up and adjust

Feather boards make work easier and faster. Feather board for table saws typically come with a slot for width adjustment andfingerpressure. They help cut tricky points while still providing enough pressure for holding down the workpiece.

2. Stability and Tension Control

Power tools are disliked for their vibration, leading to parallax error on a workpiece while cutting. However, the feather boards solve this problem for you as it comes with a tension control functionality. This functionality helps maintain stability and even pressure to ensure a smooth cutting process.

3. Strength

Feather boards provide strength and durability. Nevertheless, most manufacturers use a hybrid material comprising of composite plastic and metal.

4. Size

Featherboards come in several sizes that suit different applications. Therefore, no matter the size of the material you want to cut, you can find a suitable feather board.

5.Design Components

Featherboards come in non-magnetic and magnetic variations. Both variations serve as an attachment of the feather board to the table saw. However, the non-magnetic variations employ a standard miter slot positioning for attachment to the table.

Section 3: Should I make my feather boards or buy a ready-made?

3.1 How to choose the right feather board?

There are two significant ways that most operators acquire their feather board. They either buy from a manufacturing company or make theirs. Nevertheless, the eventual choice of which way to go depends on several factors. These factors include time constraints and whether or not you like making jigs.

The flipside to DIY feather boards is that they are harsher to use. Also, these feather boards are mostly for professionals. Depending on the type of project you are undertaking, you may need to rethink which option you take. If you are hoping to make a basic clamp to the table saw, you can opt for a shop-made feather board. However, if you intend to make cuts that will require a lot of adjustment, buy a ready-made board.

Section 4: How to make a feather board?

4.1 Cut the Stock to Size

根据工件的大小,选择一个dimension of feather board to suit the purpose. An essential rule to follow is to cut your feather board in 5×12 inches. Next, you canripyour stock accordingly before cutting to length with your miter saw.

In cutting your board length, there is an important rule you must follow. You must cut your stock according to your needs. For example, consider that the distance from your clamping point to your saw blade is 10 inches. It means you must cut your feather board to be longer than 10 inches.

4.2 Miter the Board

Next is to crosscut your board at 30 degrees with your miter saw. It is best to cut on the part of the board against which the workpiece rests.

4.3 Mark a Stop Line

From the miter edge or face, mark a point 3 inches parallel to the 30-degree lacerations. This demarcation will serve as your stop line when you start to cut the fingers of your feather board. Also, you can mark your edges with your bevel or a pencil.

4.4 Cut the Fingers

Set the fence of the table saw 1/4 inch from the cutting edge. Spot the long side of the board immovably against the fence and level on the table. Next, run the board through the saw from the mitered edge until you arrive at the stop line. At that point, cautiously withdraw the board until it securely clears the sharp edge.

把看到的引擎。与股票摇来摇去m the sharp edge, move the fence an extra 3/8-inch away from the edge. Next, make another cut parallel to the first and again up to the stop line. However, note that the saw must be consistently put off while changing the fence to prevent accidents.

Section 5: How to use a feather board?

Utilizing a feather board is a lot more secure than attempting to hold a workpiece against the fence by hand. This accessory helps to prevent kickbacks due to its design.

Off-the-shelf models typically integrate with milter slots on the table. However, it should position in the feed direction and front of the blade. This configuration is essential because it helps to prevent wastes from interfering with the cuts.

To position the feather board, lower the blade with the cutting tool off. Next, place the stock against the fence. After this, place the feather board against the stock. You should test the fit of the configuration before cutting. The blade should face down when tested. It involves moving the workpiece on the table. If the workpiece can move forward easily but hard to move backward, the fit is perfect. Once positioned, you are ready to go!

Figure: Featherboard as a guide

Featherboard as a guide

Section 6: The best feather board

1. Milescraft Featherboard

The Milescraft feather board is a versatile accessory. Its design features an attachment to miter bars of 3/4-inch and 5/8-inch dimensions. Also, it is easy to use.


  • It gives operators the freedom to place it on both sides of the blade and the fence.
  • It is extremely fast to set up due to its simple design.


  • It is only suitable for metal tables.

2. Kreg True-FLEX Featherboard

This Kreg feather board is using a plastic composite. It is suitable withbandsaws and router tables. It has a twin pack setup that allows different placement on the side of the table and top of the fence. As such, it allows even pressure and prevents accidents.


  • It is suitable with several stationary power tools.
  • This feather board helps to maintain even pressure on the workpiece.
  • It provides ease of installation.


  • It is limited in design and non-magnetic
  • There is a chance that warping will occur with this device.

3. Milescraft FeatherBoard For Table Saws, Router tables, and Fence

Milescraft has a unique design of a split track miter plate. As such, this design allows sufficient hold and consistent tension during cutting. Also, it allows for fast and easy setup due to its dual slide motion capability. Its design also features adjustment knobs, which allow easy loosening and tightening. Pros

  • It comes with all the necessary hardware needed for quick attachment.
  • This feather board allows for pre-loading tension, which is crucial for preventing kickbacks.
  • It provides a firm grip of the workpiece against the fence.


  • Its adjustment might be difficult for some users due to its curved end.

4. Magswitch – Reversible Featherboard

The Magswitch brand is known for its good work holding capability. They typically provide about 160 lbs of force to make the featherboards remain immobile. Hence, using this kit results in a clean-cut while preventing kickbacks.


  • It is reversible and suitable for outfeed and infeed applications.
  • This feather board is special engineering materials that make it lightweight.
  • It offers excellent protection against kickbacks due to its design.


  • It doesn’t provide as much grip onsteeltables as opposed to cast-iron tables.

5.Hedgehog Spiral Featherboards

The Hedgehog Spiral Featherboards features a simple spiral design and one knob to enable smooth adjustments. This design ensures your continuous operation even when using boards of multiple widths. Unlike other feather boards that require numerous adjustments, you only need to flip the dial on the Hedgehog featherboards. With this accessory, beginners will appreciate the ease of controlling the wood while only using one hand.


  • It allows one-handed use due to its single pivot.
  • This feather board provides high-quality at a lower cost.
  • It is lightweight.


  • It has no T-bar to fit the miter slot.


Featherboards are a must-have for professionals and retail woodworkers. At a relatively low price point, most woodworkers have this accessory in their catalog. This article outlines the fundamental knowledge about the feather board and why you should own one. It also gives a detailed DIY procedure if you choose to have your feather board shop-made. However, it is essential to go for a trusted manufacturer when getting a feather board.NCCuttingtoolsis your best option. We have the best products and professionals to assist you with feather boards purchase. Contact us now!

Share on facebook
Share on linkedin

Contact us for a free sample


Fill in your details and we’ll get back to you in 24 Hours.

Cookies help us deliver our services. By using our services, you agree to our use of cookies.